Shop Electrical Supplies Online
Showing 465–480 of 491 resultsSorted by popularity
Cable GlandsKSS Nylon Compression Glands With Strain Relief
KSS AG20SR Nylon Cable Gland With Strain Relief provides secure cable entry, environmental sealing and additional protection against sharp cable bending.
The extended flexible strain-relief section helps support the cable where it exits the gland, reducing stress at the entry point.
Features an M20 × 1.5 thread, suits 10–14mm cable OD, and provides IP68 protection when correctly installed.
P/N: AG20SR
- Cable Glands
Termco Standard Metal Locknuts
Termco Metal Locknut is a metal locknut for securing a matching Termco metal compression gland, in M12 to M63 threads.
P/N: MLN
- Cable Glands
Termco Standard Metal Compression Glands
Termco Metal Compression Gland is a metal compression cable gland for switchboards and enclosures, in M12 to M63 threads.
P/N: MG
- Cable Clips
KSS Nail Cable Clip (Flat)
Indeed, the flat nail cable clip secures flat cable at 9.3mm or 11.9mm width to a surface.
- Securing flat two-core cable directly to a surface
- Two listed profile widths, 9.3mm and 11.9mm
- Sites where a rubber-lined clamp is not required
Available in packs of 500 or 5000.
- Bushings, Plugs and Grommets
KSS Grommets (Closed)
This product is a closed grommet for sealing or covering an unused panel opening, listed by mounting hole size with its own slot width.
- For example, sealing or covering an unused panel opening
- Also, switchboards, control panels and electrical enclosures
- In particular, jobs needing a clean, finished appearance over a redundant opening
P/N: GMC
- Bushings, Plugs and Grommets
KSS Open Grommets – Flexible PVC Cable Grommets
KSS Open Grommets provide a smooth, flexible cable-entry point where wires and cables pass through holes in metal panels, chassis and electrical enclosures.
Manufactured from flexible black PVC, the GM series helps protect cable insulation from contact with rough or sharp panel edges.
Available for mounting holes from 6.2mm to 31.9mm.
P/N: GM Series
- Tension Sleeves
Full Tension Sleeves – Type A
Utilux Type A full tension sleeves provide full tension splices for AAC overhead transmission conductors. Each aluminium alloy sleeve includes a centre barrier and comes pre-packed with jointing compound in a sealed bag.
- Eight part numbers: FT36A to FT94A
- Hexagonal or indent crimping, with tooling matched to the conductor
- Manufacturer dimensions and selection guidance below
Check before ordering: The diameter labels for FT61A, FT68A, FT80A and FT94A differ from the Utilux manual. Select by part number and confirm suitability with Engineering Supplies on (08) 9258 8444 or sales@engsup.com.au.
- Utilux Copper Lugs & Links
Copper Narrow Palm / Circuit Breaker Lugs
Narrow Palm Lug is a narrow-palm copper lug for circuit breaker terminals, for 120mm² cable with a 10mm stud.
P/N: CGNP
- Utilux Terminals
High Temp Ring Terminals 2.5 – 6.0mm2
Utilux Large High Temp Ring Terminals – 2.5-6.0mm² are uninsulated crimp terminals with a closed ring end, designed for use in high-temperature environments where a standard insulated collar is unsuitable.
Available for conductors from 2.5mm² to 6.0mm², in a 5mm stud size, uninsulated.
P/N: UHRT3
- Utilux Terminals
High Temp Ring Terminals 0.5 – 1.5mm2
Utilux Small High Temp Ring Terminals – 0.5-1.5mm² are uninsulated crimp terminals with a closed ring end, designed for use in high-temperature environments where a standard insulated collar is unsuitable.
Available for conductors from 0.5mm² to 1.5mm², in a 5mm stud size, uninsulated.
P/N: UHRT1
- Utilux Terminals
Pin Terminals – 2.5 – 6.0mm2 Yellow
Utilux Pin Terminals – 2.5–6.0mm², Yellow are crimp terminals with a solid round pin end that inserts into a matching socket or terminal block, keeping the connection secure under vibration and movement.
Available for conductors from 2.5mm² to 6.0mm², colour-coded Yellow, in the Supergrip style, 2.8mm pin width.
P/N: UPT3
- Utilux Terminals
Pin Terminals – 1.5 – 2.5mm2 Blue
Utilux Pin Terminals – 1.5–2.5mm², Blue are crimp terminals with a solid round pin end that inserts into a matching socket or terminal block, keeping the connection secure under vibration and movement.
Available for conductors from 1.5mm² to 2.5mm², colour-coded Blue, in Insulated, Supergrip and Uninsulated styles, 2mm pin width.
P/N: UPT2
- Utilux Terminals
Pin Terminals – 0.5 – 1.5mm2 Red
Utilux Pin Terminals – 0.5–1.5mm², Red are crimp terminals with a solid round pin end that inserts into a matching socket or terminal block, keeping the connection secure under vibration and movement.
Available for conductors from 0.5mm² to 1.5mm², colour-coded Red, in Insulated, Supergrip and Uninsulated styles, 1.6mm pin width.
P/N: UPT1
- Utilux Aluminium Lugs & Links
Aluminium Unilink
This product is an aluminium connector for joining aluminium conductors, listed by cable size and Utilux part number, available in fourteen cable sizes.
- For example, joining two lengths of aluminium conductor of the same size
- Also, jobs needing a connector matched by Utilux part number rather than a generic fitting
- In particular, overhead or underground aluminium cable joints
SKU: AKLH1
- Utilux Aluminium Lugs & Links
3 Core Aluminium Sector Links
This product is a connector for joining three-core sector-shaped aluminium conductors, available in three cable sizes.
- For example, joining three-core sector-shaped aluminium cable of the same size
- Also, jobs needing a connector matched to sector conductor geometry rather than a round-conductor fitting
- In particular, overhead or underground three-core aluminium cable joints
SKU: H86
- Utilux Copper Lugs & Links
Copper Crimp Links with Solid Barrier
Copper Solid Barrier Link is a copper crimp link with a solid internal barrier, in 70mm² to 120mm² sizes.
P/N: CHSBH1
